Independent study aid. Not affiliated with or endorsed by NCEES. Always verify against the current NCEES exam specifications and reference handbook.
🎥 New: a free FE/PE worked-problems video every day — watch today’s video on YouTube

Theory explainer

Bernoulli Equation Head Loss Problems — FE/PE Civil Exam Worked Examples

Plain Bernoulli balances head between two points as if friction did not exist — and the exam knows it. The questions that actually appear use the extended form, with a head-loss term, and often a pump or turbine. The marks are won in the set-up: choosing points where the unknowns collapse, converting pressures to feet of head before they enter the balance, and never, ever dropping hL because the arithmetic looks cleaner without it.

Last reviewed: 2026-11-07. Every worked number below was independently re-solved; steps are shown in full.

Choosing points 1 and 2

The equation holds between any two points on a streamline, so the skill is picking the pair that kills the most terms:

Reservoir free surfaceThe gift point: \(V \approx 0\) (the surface barely moves) and p = atmospheric, i.e. zero gauge pressure head. Only z survives. Two reservoir surfaces reduce the equation to \(\Delta z = h_{L}\) + machine terms (Worked Problems 1, 3 and 5).
Pipe exit to atmospherep = atmospheric (zero gauge), diameter known so V follows from Q. The velocity head survives in full — it is real kinetic energy leaving the system (Worked Problem 4).
Pressure tapp is given (convert it: \(\frac{p}{\gamma}\)), diameter is known, z is usually given or shared with the other tap. Two taps isolate \(h_{L}\) between them (Worked Problem 2).
Anywhere mid-pipe without dataAvoid. A point with unknown pressure and unknown velocity leaves the equation with two unknowns and no way forward — move the point to a surface, an exit or a tap.

The head-loss term: three forms the exam uses

hL is the same physical loss in every problem; only its packaging changes:

Given outright"The head loss is 6 ft." Substitute directly — the question is then testing points, conversions and signs, not friction.
Darcy-Weisbach + fittings\(h_{L} = [f \cdot (\frac{L}{D}) + \Sigma K] \cdot (\frac{V^{2}}{2 g})\): friction along the pipe plus entrance, exit, bend and valve coefficients, all multiplying the velocity head of the pipe they sit in. Building f is a problem in itself — see the Darcy-Weisbach worked examples.
Lumped coefficient"Total losses are 5.3 velocity heads." Then \(h_{L} = 5.3 \cdot (\frac{V^{2}}{2 g})\) — one multiplication, but the coefficient multiplies the velocity head of the stated diameter, and no other (Worked Problem 4).

Either way, \(h_{L}\) always acts against the flow: it is head the fluid no longer has at point 2. It never changes sign, and it is never zero in a real pipe — a stem that gives you a friction factor, a roughness or a K value is telling you the loss belongs in the balance.

Pumps and turbines

A pump adds head between the points, so hpump appears on the point-1 side; a turbine extracts head, so hturbine appears on the point-2 side, next to hL. The head a machine handles converts to water power in one line, P = γ·Q·h — for a pump that is the power delivered to the water (divide by efficiency for shaft input); for a turbine it is the power taken from the water (multiply by efficiency for shaft output). Worked Problems 3 and 5 run each case.

Worked problem 1 Reservoir to reservoir: discharge from a head budget (FE pace, US units)

Given: two reservoirs with surfaces 15 ft apart are connected by an 8-inch pipe. Total head loss in the pipe is \(h_{L} = 60 \cdot (\frac{V^{2}}{2 g})\). Find the discharge.

Solution:

  1. Points: both free surfaces. At each, \(V \approx 0\) and p is atmospheric, so the equation collapses to \(z_{1} - z_{2} = h_{L}\).
  2. \(15 = 60 \cdot (\frac{V^{2}}{2 g})\), so the velocity head is \(\frac{V^{2}}{2 g} = \frac{15}{60}\) = 0.250 ft
  3. \(V = \sqrt{2 \times 32.2 \times 0.250} = \sqrt{16.1}\) = 4.01 \(\frac{\text{ft}}{s}\)
  4. \(A = \pi \cdot \frac{(\frac{8}{12})^{2}}{4}\) = \(0.349\,\text{ft}^{2}\); \(Q = V \cdot A = 4.01 \times 0.349\) = 1.40 cfs

Answer: \(Q \approx 1.40\) cfs. Trap note: the exit velocity head is not added separately here — it is inside the stem's total-loss coefficient, which is what "total" means. Candidates who add another \(\frac{V^{2}}{2 g}\) double-count it; candidates who use the pipe diameter in inches corrupt A by a factor of 144.

Worked problem 2 Constriction: head loss from two pressure taps (PE pace, US units)

Given: water flows at \(Q = 3\) cfs through a horizontal pipe that contracts from 12 inches to 6 inches. Pressure taps read \(p_{1} = 20\,\text{psi}\) in the 12-inch section and \(p_{2} = 12\,\text{psi}\) in the 6-inch section. Find the head loss between the taps.

Solution:

  1. Continuity first: \(A_{1} = \pi \cdot \frac{(1.0)^{2}}{4} = 0.785\,\text{ft}^{2}\), \(V_{1} = \frac{3}{0.785}\) = 3.82 \(\frac{\text{ft}}{s}\), velocity head = \(\frac{3.82^{2}}{64.4}\) = 0.227 ft
  2. \(A_{2} = \pi \cdot \frac{(0.5)^{2}}{4} = 0.196\,\text{ft}^{2}\), \(V_{2} = \frac{3}{0.196}\) = 15.28 \(\frac{\text{ft}}{s}\), velocity head = \(\frac{15.28^{2}}{64.4}\) = 3.625 ft — quartering the area quadruples the velocity and multiplies its head by sixteen.
  3. Pressures to head: \(\frac{p_{1}}{\gamma} = 20 \times \frac{144}{62.4}\) = 46.15 ft; \(\frac{p_{2}}{\gamma} = 12 \times \frac{144}{62.4}\) = 27.69 ft. Same centreline elevation, so z cancels.
  4. \(h_{L} = (46.15 + 0.227) - (27.69 + 3.625) = 46.38 - 31.32\) = 15.06 ft

Answer: \(h_{L} \approx 15.1\,\text{ft}\). Trap note: most of the pressure drop is not loss — it is pressure head converted into velocity head as the pipe narrows, and only the 15.06 ft balance is truly lost. Using the 12-inch velocity head on both sides (or the 6-inch on both) is the classic wrong-diameter error this question exists to catch.

Worked problem 3 Pump head to an upper tank (PE pace, US units)

Given: a pump lifts water at \(Q = 2\) cfs from a reservoir (surface elevation 10 ft) to an upper tank (surface elevation 85 ft) through an 8-inch pipe. Total head loss is \(h_{L} = 6 \cdot (\frac{V^{2}}{2 g})\). Find the pump head and the water power.

Solution:

  1. Points: the two free surfaces, so both velocity and pressure heads vanish and the equation reads \(h_{\text{pump}} = (z_{2} - z_{1}) + h_{L}\).
  2. Pipe velocity: \(V = \frac{Q}{A} = \frac{2}{0.349}\) = 5.73 \(\frac{\text{ft}}{s}\); velocity head = \(\frac{5.73^{2}}{64.4}\) = 0.510 ft
  3. \(h_{L} = 6 \times 0.510\) = 3.06 ft
  4. \(h_{\text{pump}} = (85 - 10) + 3.06\) = 78.06 ft
  5. Water power: \(P = \gamma \cdot Q \cdot h = 62.4 \times 2 \times 78.06 = 9742\,\text{ft}\)·lbf/\(s \div 550\) = 17.7 hp (before pump efficiency)

Answer: \(h_{\text{pump}} \approx 78.1\,\text{ft}\); water power ≈ 17.7 hp. Trap note: the static lift \((75\,\text{ft})\) is not the pump head — the pump must also pay the 3.06 ft of loss, and a stem that hands you a loss coefficient expects it in the answer. Shaft power would be higher still: divide by the pump efficiency, never multiply.

Worked problem 4 The trap: ignoring \(h_{L}\) (the 44.6 vs 17.8 cfs question)

Given: an upper reservoir drains through 450 ft of 18-inch pipe \((f = 0.016, entrance K = 0.5)\) to an exit 9.9 ft below the reservoir surface. Find the discharge — and see what plain Bernoulli would have told you.

Solution:

  1. Loss coefficient: \(f \cdot (\frac{L}{D}) = 0.016 \times (\frac{450}{1.5}) = 4.8\); plus the entrance, total = \(4.8 + 0.5\) = 5.3 velocity heads, so \(h_{L} = 5.3 \cdot (\frac{V^{2}}{2 g})\).
  2. Points: reservoir surface (\(V \approx 0\), p atmospheric) to the pipe exit (p atmospheric, full velocity head). The 9.9 ft drop splits into kinetic energy plus loss: \(9.9 = \frac{V^{2}}{2 g} + 5.3 \cdot (\frac{V^{2}}{2 g}) = 6.3 \cdot (\frac{V^{2}}{2 g})\).
  3. Velocity head = \(\frac{9.9}{6.3}\) = 1.571 ft; \(V = \sqrt{64.4 \times 1.571} = \sqrt{101.2}\) = 10.06 \(\frac{\text{ft}}{s}\)
  4. \(A = \pi \cdot \frac{(1.5)^{2}}{4} = 1.767\,\text{ft}^{2}\); \(Q = 10.06 \times 1.767\) = 17.8 cfs
  5. Ignoring \(h_{L}\): all 9.9 ft becomes velocity head, \(V = \sqrt{64.4 \times 9.9} = 25.25\,\text{ft}/\text{s}\) and Q = 44.6 cfs — two and a half times the truth.

Answer: \(Q \approx 17.8\) cfs (44.6 cfs if head loss is ignored). Trap note: this is the trap from our 60-second Short on this exact question — friction took 5.3 of every 6.3 feet of head, leaving almost nothing for velocity. Whenever a stem gives roughness, an f value or K coefficients and your method produces a Torricelli-style \(\sqrt{2 g \Delta z}\) answer, you have solved the frictionless distractor.

Worked problem 5 Turbine: head extracted and power out (PE pace, US units)

Given: a penstock carries \(Q = 30\) cfs from an upper reservoir (surface elevation 210 ft) through a turbine to a tailwater surface at elevation 150 ft. Total head loss in the penstock is 6 ft. Find the turbine head and the shaft power at 85% efficiency.

Solution:

  1. Points: the two free surfaces again — velocity and pressure heads vanish at both ends, leaving \(z_{1} = z_{2} + h_{\text{turbine}} + h_{L}\).
  2. \(h_{\text{turbine}} = 210 - 150 - 6\) = 54 ft — the elevation drop pays the losses first; the turbine gets what is left.
  3. Hydraulic power in the water at the turbine: \(P = \gamma \cdot Q \cdot h = 62.4 \times 30 \times 54 = 101088\,\text{ft}\)·lbf/s = 183.8 hp
  4. Shaft output at 85% efficiency: \(0.85 \times 183.8\) = 156 hp \((≈ 116\,\text{kW})\)

Answer: \(h_{\text{turbine}} = 54\,\text{ft}\); shaft power ≈ 156 hp. Trap note: efficiency multiplies for a turbine (output is less than the water power) and divides for a pump (input is more than the water power) — reversing them is a standing distractor. And crediting the turbine with the full 60 ft drop, losses unpaid, overstates the head by the whole \(h_{L}\).

Frequently asked questions

What is the extended Bernoulli equation?

The head-form balance z1 + p1/γ + V1²/2g + hpump = z2 + p2/γ + V2²/2g + hturbine + hL — Bernoulli plus the three real-world terms: machine head added, machine head extracted, and head lost. Every term is in feet or metres of the flowing fluid.

How do you convert psi to feet of head?

Head = p/γ. For water, 1 psi = 144/62.4 = 2.31 ft, so 20 psi = 46.2 ft of head. Convert before substituting — never let psi enter a head balance directly.

How should points 1 and 2 be chosen?

Where the most is known: reservoir surfaces (V ≈ 0, p atmospheric), pipe exits (p atmospheric, known diameter) and pressure taps (known p and diameter). Two reservoir surfaces collapse the equation to Δz against losses and machine head alone.

What happens if head loss is ignored in a Bernoulli problem?

Velocities and discharges come out too high — in Worked Problem 4, 44.6 cfs instead of 17.8 cfs, a factor of about 2.5. Friction is not a refinement on these problems; it is most of the head budget.

Where do pump and turbine terms go in the equation?

hpump on the upstream (point-1) side — it adds head. hturbine on the downstream (point-2) side with hL — it removes head. Water power is P = γ·Q·h in either case; divide by efficiency for pump input, multiply for turbine output.

Free FE/PE flashcards + study tips, by email

Join the Water Resources Hub email list and get the free 40 water-resources flashcards (PDF + Anki) straight away, then study tips and practice problems by email. Email address only — no spam, unsubscribe any time.