Theory explainer
Darcy-Weisbach Equation Practice Problems — FE/PE Civil Exam Worked Examples
Almost every pipe-flow question on the FE/PE Civil exams passes through one equation: the Darcy-Weisbach head-loss equation. The equation itself is one line — the exam points are won or lost on the friction factor, on the diameter-to-the-fifth-power scaling, and on not confusing the Darcy factor with the Fanning factor. Learn those three, and the whole family of friction-loss questions collapses to a short, checkable routine.
Last reviewed: 2026-11-07. Every worked number below was independently re-solved; steps are shown in full.
The equation in its useful forms
The head form is the one the exam asks for, but two rearrangements save time. At fixed discharge, substituting V = 4Q/(πD²) gives the Q-form, which exposes the D−5 scaling that drives the ratio questions. And the pressure form converts head loss to a pressure drop in one step:
\[h_{f} = f \cdot (\frac{L}{D}) \cdot (\frac{V^{2}}{2 g})\] \(h_{f} = 0.0826 \cdot f \cdot L \cdot \frac{Q^{2}}{D^{5}}\) (SI) \(h_{f} = 0.0252 \cdot f \cdot L \cdot \frac{Q^{2}}{D^{5}}\) (US, Q in cfs, L and D in ft)
The constants 0.0826 and 0.0252 are just \(\frac{8}{(\pi^{2} g)} \text{in}\) each unit system \((g = 9.81\,\text{m}/\text{s}^{2} and 32.2\,\text{ft}/\text{s}^{2})\). If you remember the head form, you can re-derive the Q-form on the spot — but the D−5 in it is worth memorising, because it is the whole content of the "halve the diameter" question (Worked Problem 4).
Finding f: regime first, chart second
The friction factor is where the physics lives. It depends on the flow regime, and the regime is decided by the Reynolds number:
| Laminar, Re < ~2,000 | \(f = \frac{64}{Re}\) exactly — roughness does not matter; the pipe wall is buried inside a thick laminar layer. (Some texts draw the line at 2,300; the exam rarely tests the boundary itself.) |
|---|---|
| Transitional, ~\(2000 < Re\) < ~4,000 | Unstable — f is not reliably predicted. Exam stems avoid this band, or give f outright. If your Re lands here, re-check your viscosity and diameter conversions before anything else. |
| Turbulent, Re > ~4,000 | f depends on both Re and the relative roughness \(\frac{\epsilon}{D}\). Read it from the Moody chart, or compute it from the Colebrook equation: \(\frac{1}{\sqrt{f}} = -2 \cdot \log_{10} (\frac{\epsilon}{(3.7 D)} + \frac{2.51}{(Re \cdot \sqrt{f})})\). Colebrook is implicit in f, so iterate from a first guess (\(f \approx 0.02\) is a good start) — or use the explicit Haaland approximation: \(\frac{1}{\sqrt{f}} \approx -1.8 \cdot \log_{10} [(\frac{\frac{\epsilon}{D}}{3.7})^{1.11} + \frac{6.9}{Re}]\), accurate to about 2%. |
Two limiting cases are worth knowing for sanity checks. In the fully rough turbulent regime (very high Re), f stops depending on Re and depends only on \(\frac{\epsilon}{D}\) — the Moody chart curves flatten. In a hydraulically smooth pipe \((\epsilon \approx 0)\), f depends only on Re. If your computed f falls outside roughly 0.008–0.05 for a water pipe, something upstream of it is wrong.
Pipe roughness: the table the exam expects you to know how to use
Absolute roughness ε is a property of the pipe material and condition. The exam either gives it or expects a standard value from a table like this one; either way, what enters Colebrook and the Moody chart is the relative roughness ε/D, so ε and D must be in the same units:
| PVC / HDPE, new | \(\epsilon = 0.0015\,\text{mm}\) = 0.000005 ft — effectively smooth |
|---|---|
| Drawn copper / brass, new | \(\epsilon = 0.0015\,\text{mm}\) = 0.000005 ft |
| Commercial steel, new | \(\epsilon = 0.046\,\text{mm}\) = 0.00015 ft — the default when no material is stated |
| Galvanised steel, new | \(\epsilon = 0.15\,\text{mm}\) = 0.0005 ft |
| Cast iron, new | \(\epsilon = 0.26\,\text{mm}\) = 0.00085 ft |
| Concrete, smooth | \(\epsilon = 0.3\)–1.0 mm depending on formwork |
| Old water mains (tuberculated cast iron) | \(\epsilon = 3.0\)–6.0 mm — ageing can raise ε by an order of magnitude, which is why old-pipe questions give ε explicitly |
Worked problem 1 Head loss and pressure drop, f given (FE pace, US units)
Given: water flows at \(V = 4\,\text{ft}/\text{s}\) through 500 ft of 6-inch pipe, Darcy friction factor \(f = 0.02\). Find the friction head loss and the pressure drop.
Solution:
- Convert the diameter: \(D = 6\,\text{in}\) = 0.50 ft — the step candidates most often skip, and the one that corrupts everything after it.
- Velocity head: \(\frac{V^{2}}{2 g} = \frac{16}{(2 \times 32.2)} = \frac{16}{64.4}\) = 0.2484 ft
- \(h_{f} = f \cdot (\frac{L}{D}) \cdot (\frac{V^{2}}{2 g}) = 0.02 \times (\frac{500}{0.50}) \times 0.2484 = 0.02 \times 1000 \times 0.2484\) = 4.97 ft
- Pressure drop: \(\Delta p = \gamma \cdot h_{f} = 62.4 \times 4.97 = 310\,\text{lb}/\text{ft}^{2}\) = 2.15 psi (dividing by \(144\,\text{in}^{2}/\text{ft}^{2}\))
Answer: \(h_{f} \approx 4.97\,\text{ft}\); \(\Delta p \approx 2.15\,\text{psi}\). Trap note: 4.97 ft is a head, not a pressure — answering "4.97 psi" confuses the two quantities the stem distinguishes, and forgetting the /144 conversion gives 310 psi, an absurd answer that should trigger a re-check.
Worked problem 2 Laminar flow: f from Re (FE pace, US units)
Given: water at 68 °\(F (\nu = 1.08 \times 10^{-5} \frac{\text{ft}^{2}}{s})\) flows at \(V = 0.20\,\text{ft}/\text{s}\) through 100 ft of 1-inch pipe. Find the friction head loss.
Solution:
- \(D = 1\,\text{in}\) = 0.08333 ft
- \(Re = V \cdot \frac{D}{\nu} = 0.20 \times \frac{0.08333}{(1.08 \times 10^{-5})}\) = 1,543 — laminar, so roughness is irrelevant and f is exact.
- \(f = \frac{64}{Re} = \frac{64}{1543}\) = 0.0415
- Velocity head: \(\frac{V^{2}}{2 g} = \frac{0.04}{64.4}\) = 0.000621 ft
- \(h_{f} = 0.0415 \times (\frac{100}{0.08333}) \times 0.000621 = 0.0415 \times 1200 \times 0.000621\) = 0.031 ft
Answer: \(h_{f} \approx 0.031\,\text{ft}\). Trap note: the tiny answer is the point — laminar flow at low velocity loses almost nothing to friction, because the velocity head itself is tiny. A candidate who reaches for the Moody chart here, or who uses a turbulent \(f \approx 0.02\), has skipped the regime check that the question exists to test.
Worked problem 3 Turbulent flow: f from Haaland (PE pace, US units)
Given: water at 68 °F flows at \(V = 5\,\text{ft}/\text{s}\) through 1,000 ft of 12-inch commercial steel pipe \((\epsilon = 0.00015\,\text{ft})\). Find the friction head loss.
Solution:
- \(D = 12\,\text{in}\) = 1.00 ft; relative roughness \(\frac{\epsilon}{D} = \frac{0.00015}{1.00}\) = 0.00015
- \(Re = V \cdot \frac{D}{\nu} = 5 \times \frac{1.00}{(1.08 \times 10^{-5})}\) = 462,963 — well into turbulent flow, so f needs both Re and \(\frac{\epsilon}{D}\).
- Haaland: \(\frac{1}{\sqrt{f}} = -1.8 \cdot \log_{10} [(\frac{0.00015}{3.7})^{1.11} + \frac{6.9}{462963}] = -1.8 \cdot \log_{10} (2.823 \times 10^{-5}) = -1.8 \times (−4.5493) = 8.189\), so \(\sqrt{f} = 0.1221\) and \(f = 0.0149\)
- Velocity head: \(\frac{V^{2}}{2 g} = \frac{25}{64.4}\) = 0.3882 ft
- \(h_{f} = 0.0149 \times (\frac{1000}{1.00}) \times 0.3882\) = 5.79 ft
Answer: \(f \approx 0.0149\); \(h_{f} \approx 5.79\,\text{ft}\). Trap note: the Haaland arithmetic is the only long step — keep all four significant figures in the log argument, because f sits inside a square root and a small slip in the exponent moves the answer more than the ~1% Haaland error ever will. A Moody-chart read of the same point gives \(f \approx 0.015\), a useful cross-check.
Worked problem 4 The ratio question: halve the diameter (exam trap, no calculator needed)
Given: a pipe carrying a fixed discharge Q is replaced by a pipe of half the diameter, all else (including f) unchanged. By what factor does the friction head loss change? And what if the velocity, not the discharge, were held constant?
Solution:
- At fixed Q, use the Q-form: \(h_{f}\) ∝ \(\frac{1}{D^{5}}\). Halving D gives \(\frac{h_{f,new}}{h_{f,old}} = (\frac{D}{D_{new}})^{5} = 2^{5}\) = 32. A pipe that lost 2.0 ft now loses 64 ft.
- At fixed V, use the head form: \(h_{f}\) ∝ \(\frac{1}{D}\). Halving D only doubles \(h_{f}\).
Answer: ×32 at fixed discharge; ×2 at fixed velocity. Trap note: the stem's held-constant quantity is the whole question. "Same flow" means same \(Q (×32)\); "same velocity" means V fixed \((×2)\). The factor-32 answer is also why small-diameter pipes dominate the head loss in a network — and why the exam returns to it so often.
Worked problem 5 The inverse question: discharge from a head budget (PE pace, US units)
Given: a 2,000 ft length of 12-inch pipe \((f = 0.02)\) may lose at most \(h_{f} = 10\,\text{ft}\). What discharge can it carry?
Solution:
- \(D = 1.00\,\text{ft}\). US Q-form: \(h_{f} = 0.0252 \cdot f \cdot L \cdot \frac{Q^{2}}{D^{5}}\), so \(Q^{2} = h_{f} \cdot \frac{D^{5}}{(0.0252 \cdot f \cdot L)} = 10 \times \frac{1}{(0.0252 \times 0.02 \times 2000)} = \frac{10}{1.008} = 9.921\)
- \(Q = \sqrt{9.921}\) = 3.15 cfs
- Check: \(V = \frac{Q}{A} = \frac{3.15}{(\pi \times \frac{1^{2}}{4})} = \frac{3.15}{0.7854} = 4.01\,\text{ft}/\text{s}\); \(h_{f} = 0.02 \times 2000 \times (\frac{4.01^{2}}{64.4}) = 0.02 \times 2000 \times 0.2497 = 9.99\,\text{ft}\) ✓
Answer: \(Q \approx 3.15\) cfs \((V \approx 4.01\,\text{ft}/\text{s})\). Trap note: the back-substitution check is cheap and catches the two classic slips — diameter left in inches (which inflates Q by a factor of \(12^{2.5}\)) and the Q-form constant used in the wrong unit system.
Frequently asked questions
What is the Darcy-Weisbach equation?
hf = f·(L/D)·(V²/2g): the head loss due to wall friction in a pipe flowing full, where f is the Darcy friction factor, L the length, D the diameter, V the mean velocity and g gravitational acceleration. The pressure drop is Δp = γ·hf.
How is the Darcy friction factor found?
Compute Re = V·D/ν first. Laminar (Re below about 2,000): f = 64/Re. Turbulent (Re above about 4,000): f depends on Re and the relative roughness ε/D, read from the Moody chart or computed from the Colebrook equation; Haaland's equation is an explicit approximation to Colebrook.
What is the difference between the Darcy and Fanning friction factors?
The Darcy factor is four times the Fanning factor: f = 4·Cf. Both give the same head loss when used in their own form of the equation — the error is applying the factor of 4 twice, or using a Fanning value in the Darcy equation unconverted.
How does head loss change if the pipe diameter is halved at the same discharge?
By a factor of 32, because at fixed Q, hf scales as 1/D5. At fixed velocity it only doubles, because then hf scales as 1/D. The stem's held-constant quantity decides the exponent.
Does the Darcy-Weisbach equation cover minor losses from fittings?
No — it covers straight-pipe friction only. Total head loss adds the fitting terms: hL = hf + ΣK·(V²/2g). A stem listing K values is asking for the total.
When should Hazen-Williams be used instead of Darcy-Weisbach?
Only when the stem gives a Hazen-Williams coefficient C or asks for a Hazen-Williams result. Hazen-Williams is a water-only empirical shortcut; Darcy-Weisbach is the general method for any fluid, regime and material.
Free FE/PE flashcards + study tips, by email
Join the Water Resources Hub email list and get the free 40 water-resources flashcards (PDF + Anki) straight away, then study tips and practice problems by email. Email address only — no spam, unsubscribe any time.