Independent study aid. Not affiliated with or endorsed by NCEES. Always verify against the current NCEES exam specifications and reference handbook.
🎥 New: a free FE/PE worked-problems video every day — watch today’s video on YouTube

Theory explainer

Orifice Flow Problems — FE/PE Civil Exam Worked Examples

An orifice is the simplest flow device on the exam — a hole in a tank wall — and the questions it generates are almost entirely about three coefficients and one square root. Learn Torricelli's velocity, the Cd = Cc × Cv split, and the falling-head time integral, and the whole family (constant head, submerged, tank emptying, jet trajectory) collapses to a few lines each.

Last reviewed: 2026-11-04. Every worked number below was independently re-solved; steps are shown in full.

Where Torricelli's equation comes from

Apply Bernoulli between the tank surface (velocity ≈ 0, pressure atmospheric, elevation H above the orifice) and the jet at the orifice (pressure atmospheric, elevation 0). The pressure terms cancel, the surface velocity vanishes, and what survives is Vth = √(2gH) — the same speed a dropped object reaches after falling H. That is why the exam treats an orifice as a falling-body problem with a hole in it: discharge grows with the square root of head, so doubling the head raises discharge by only √2 ≈ 1.41, and quadrupling the head doubles it. Any answer choice showing discharge scaling linearly with head is a distractor.

Real jets fall short of the ideal in two ways. First, streamlines cannot turn the sharp corner of the orifice edge, so the jet keeps contracting for about half a diameter past the plate and reaches its minimum cross-section — the vena contracta — there, not at the plate. Second, friction in the orifice itself costs a little velocity. Hence Cd = Cc × Cv, with textbook sharp-edged values Cc ≈ 0.62, Cv ≈ 0.98, Cd ≈ 0.61. A rounded or well-shaped orifice raises Cd toward 1.0; a sharp-edged plate is the exam default, so if a stem gives no coefficient, 0.61–0.62 is the value to reach for — but only if the stem genuinely omits it.

Constant head: the workhorse problem

With the head held constant (a large reservoir, a regulated inflow), discharge is a single substitution: Q = Cd·A·√(2gH). Watch three things: diameter in inches converted to feet before squaring (the classic slip — a 3-inch orifice is 0.25 ft, and its area is 0.0491 ft², not 7.07 in some mixed unit), g = 32.2 ft/s² in US units, and head measured to the centreline. Worked Problem 1 is the template; the ratio variant (two orifices, same diameter, heads in ratio 16:25) is the one-line version the exam loves — discharges scale as √(h1/h2) = 4:5, with Cd and area cancelling outright.

Finding the coefficients from measurements

Two measurement families appear, and each isolates one coefficient. The trajectory method isolates Cv: a jet leaving horizontally with actual velocity Va travels x horizontally while falling y vertically, so Va = x·√(g/2y) from projectile motion, and Cv = Va/√(2gH) = x/√(4yH). The jet-diameter method isolates Cc: measure the jet diameter at the vena contracta and Cc = (djet/dorifice)², since areas scale with diameter squared. A stem handing you both a trajectory and a measured discharge is asking for all three coefficients in sequence — Cv from the trajectory, Cd from Q/(A√(2gH)), then Cc = Cd/Cv.

Submerged orifices: head becomes a difference

When the downstream side is also under water — an orifice connecting two tanks, or a submerged outlet — the jet discharges against a tailwater, not the atmosphere. The driving head is then the difference between the upstream and downstream water levels, ΔH = H1 − H2, both measured from the same orifice centreline, and Q = Cd·A·√(2g·ΔH). Using the full upstream head here is the trap: it overstates discharge, by about a third in Worked Problem 4. The same rule governs submerged weirs and culvert outlets — whenever both sides are wet, only the difference drives flow.

Falling head: tank emptying time

When the tank drains, the head falls as it drains, so discharge falls too — the last foot takes far longer than the first. Integrating dV = −Q·dt with Q = Cd·Ao·√(2gh) over a tank of constant plan area As gives t = 2As(√h1 − √h2)/(Cd·Ao·√(2g)). Two exam consequences: the factor 2 is not optional (forgetting it halves the answer), and emptying to zero head (h2 = 0) is just the same formula with the second root dropped — the time to drain completely is not twice the time to drain halfway, because the √h terms do not work that way. If the tank area varies with depth (a pond with sloping sides), the constant-area formula does not apply directly — slice it by elevation and sum, which is a design calculation rather than an FE one-liner.

Worked problem 1 Constant-head discharge (FE pace, US units)

Given: a 3-inch-diameter sharp-edged orifice in a tank wall, head H = 6 ft held constant, Cd = 0.62. Find the discharge.

Solution:

  1. Convert the diameter: d = 3 in = 0.25 ft. Area A = (π/4)(0.25)² = 0.0491 ft²
  2. Torricelli velocity: Vth = √(2 × 32.2 × 6) = √386.4 = 19.66 ft/s
  3. Q = Cd·A·Vth = 0.62 × 0.0491 × 19.66 = 0.598 cfs

Answer: Q ≈ 0.60 cfs. Trap note: leaving the diameter in inches gives an area 144 times too large — if your discharge looks absurd (tens of cfs from a 3-inch hole), the inch-to-foot conversion is where it went wrong.

Worked problem 2 Velocity and contraction coefficients from a jet (FE pace, US units)

Given: an orifice under H = 6 ft head issues a horizontal jet that travels 11.5 ft horizontally while falling 6 ft vertically. The measured discharge coefficient is Cd = 0.61. Find Cv and Cc.

Solution:

  1. Projectile motion: the jet's time of fall is t = √(2y/g), so Va = x/t = x·√(g/2y). The velocity coefficient is Cv = Va/√(2gH) = x/√(4yH).
  2. Cv = 11.5/√(4 × 6 × 6) = 11.5/√144 = 11.5/12.0 = 0.958
  3. Cc = Cd/Cv = 0.61/0.958 = 0.637 — close to the textbook sharp-edged value of about 0.62, as expected.

Answer: Cv ≈ 0.96, Cc ≈ 0.64. Trap note: Cv can never exceed 1 — if your trajectory arithmetic gives Cv above 1, the x and y (or the head) have been swapped or misread.

Worked problem 3 Tank emptying time, falling head (FE pace, US units)

Given: a tank of constant plan area As = 50 ft² drains through a 3-inch orifice, Cd = 0.62. How long for the head to fall from 8 ft to 2 ft?

Solution:

  1. Orifice area: Ao = (π/4)(0.25)² = 0.0491 ft²
  2. t = 2As(√h1 − √h2)/(Cd·Ao·√(2g)) = 2 × 50 × (√8 − √2)/(0.62 × 0.0491 × √64.4)
  3. √8 − √2 = 2.828 − 1.414 = 1.414; denominator = 0.62 × 0.0491 × 8.025 = 0.2442
  4. t = 100 × 1.414/0.2442 = 579 s ≈ 9.65 min

Answer: about 9.7 minutes. Trap note: the factor 2 in the numerator is the integral's doing — dropping it gives 4.8 minutes, a plausible-looking wrong answer that the exam will offer.

Worked problem 4 Submerged orifice between two tanks (PE pace, US units)

Given: a 6-inch orifice, Cd = 0.62, connects two tanks. The upstream level is 7 ft above the orifice centreline and the downstream level is 3 ft above it. Find the discharge, and compare with free discharge under the upstream head alone.

Solution:

  1. Driving head: ΔH = 7 − 3 = 4 ft (not 7 ft — the tailwater pushes back)
  2. Area: A = (π/4)(0.50)² = 0.1963 ft²
  3. Q = 0.62 × 0.1963 × √(2 × 32.2 × 4) = 0.62 × 0.1963 × 16.05 = 1.95 cfs
  4. Free discharge under 7 ft alone would be 0.62 × 0.1963 × √(450.8) = 2.58 cfs — submergence cuts discharge by about 24%.

Answer: Q ≈ 1.95 cfs (versus 2.58 cfs free). Trap note: 2.58 cfs is the answer the stem is baiting — it is the number you get by ignoring the tailwater entirely.

Worked problem 5 Constant-head discharge (SI units)

Given: a 50 mm orifice under a constant head of 3 m, Cd = 0.62. Find the discharge.

Solution:

  1. Area: A = (π/4)(0.050)² = 0.001963 m²
  2. Vth = √(2 × 9.81 × 3) = √58.86 = 7.673 m/s
  3. Q = 0.62 × 0.001963 × 7.673 = 0.00934 m³/s = 9.34 L/s

Answer: Q ≈ 9.34 L/s. Trap note: millimetres to metres before squaring — a 50 mm diameter is 0.050 m, and its area is 0.00196 m²; squaring 50 instead gives an answer a million times too large.

Frequently asked questions

What is Torricelli's equation?

The theoretical jet velocity from an orifice: V = √(2gH), where H is the head from the free surface to the orifice centreline. It is the speed a body reaches falling freely through height H, and it follows directly from Bernoulli's equation between the tank surface and the jet.

What is the difference between Cd, Cc and Cv?

Cv (about 0.98) is the ratio of actual to theoretical jet velocity — friction's effect. Cc (about 0.62) is the ratio of the jet area at the vena contracta to the orifice area — contraction's effect. Cd (about 0.61) is their product and the ratio of actual to theoretical discharge — the number used in Q = Cd·A·√(2gH).

How is tank emptying time calculated?

For a tank of constant plan area As draining through an orifice of area Ao: t = 2As(√h1 − √h2)/(Cd·Ao·√(2g)). The factor 2 comes from integrating the falling head; the last foot of head takes much longer to drain than the first.

What head drives a submerged orifice?

The difference between the upstream and downstream water levels, ΔH = H1 − H2, both measured from the orifice centreline. A submerged orifice discharging against a tailwater flows less than the same orifice discharging freely under the upstream head alone.

What is the vena contracta?

The narrowest section of the jet, about half an orifice diameter downstream of the plate, where the streamlines have finished contracting. Its area is about 62% of the orifice area for a sharp-edged opening — the physical origin of Cc.

What value of Cd should I use if the exam gives none?

For a sharp-edged orifice, about 0.61–0.62 is the standard textbook value. But treat this as a last resort: exam stems that intend a numerical discharge normally state Cd, and a rounded orifice or a tube can raise it substantially toward 1.0.

Free FE/PE flashcards + study tips, by email

Join the Water Resources Hub email list and get the free 40 water-resources flashcards (PDF + Anki) straight away, then study tips and practice problems by email. Email address only — no spam, unsubscribe any time.