Independent study aid. Not affiliated with or endorsed by NCEES. Always verify against the current NCEES exam specifications and reference handbook.
🎥 New: a free FE/PE worked-problems video every day — watch today’s video on YouTube

PE Civil: Water Resources & Environmental — free theory

Soil Mechanics — PE Civil (Water Resources & Environmental)

Soil Mechanics is a compact 3–5 question area on the PE Civil WRE exam, but it underpins the much larger Project Sitework area: every earthwork quantity, excavation support decision, and erosion-control design leans on the ideas below. The exam tests a short list of principles — effective stress, consolidation, shear strength, bearing capacity, slope stability, and lateral earth pressure — each reducible to one governing equation plus one classic trap.

Last reviewed: 2026-11-06. Every worked number below was independently re-solved; steps are shown in full.

Watch: Soil Mechanics in 3 minutes — effective stress, consolidation, shear strength and bearing capacity, the formulas that matter for the PE Civil WRE exam. Watch on YouTube

Effective stress: the stress the soil skeleton feels

Total vertical stress σv is the weight of everything above a point: soil plus water. Pore water pressure u carries part of that load but contributes nothing to the soil's strength or stiffness — water has no shear strength. The effective stress σ′v = σv − u is the portion carried grain-to-grain, and it governs everything: shear strength, consolidation, and bearing capacity are all functions of effective stress, never total stress.

Below the water table with hydrostatic conditions, u = γw · zw where zw is the depth below the water table. The exam's favourite twist is seepage: downward seepage increases effective stress (the drag of the flowing water adds to the grain contact force), upward seepage decreases it. Upward seepage with a hydraulic gradient approaching the critical gradient (ic ≈ 1.0 for most soils) drives effective stress toward zero — the quick (boiling) condition, where the soil loses all strength. If a question mentions upward flow and asks about stability, check the gradient against critical first.

Consolidation: settlement on a timer

When a saturated clay is loaded, the water initially carries the extra stress (excess pore pressure), then drains out slowly — the soil skeleton compresses as the water leaves. That time-dependent volume change is primary consolidation. The amount of settlement comes from the e–log p curve:

For a normally consolidated layer, primary consolidation settlement is sc = [H0 / (1 + e0)] · Cc · log10[( σ′v0 + Δσavg) / σ′v0], with stresses taken at the layer midpoint (or the layer split into sublayers for thick strata). The rate of settlement is a separate question: the time factor Tv = cv · t / Hdr², where cv is the coefficient of consolidation and Hdr is the longest drainage path — half the layer thickness for doubly drained clay, the full thickness for singly drained. Tv = 0.848 marks 90% consolidation (U = 90%), the value the exam reaches for most often.

Shear strength: Mohr–Coulomb and the three tests

Soil fails in shear along a plane when τf = c + σ′n · tan φ — the Mohr–Coulomb criterion. Cohesion c and friction angle φ come from laboratory tests, and the drainage conditions of the test must match the field problem:

Match the test to the loading rate: rapid construction on clay → UU parameters; long-term slope or foundation performance → drained (CD) parameters. Sands and gravels are always analysed drained — they consolidate during construction, so φ = 0 never applies to them.

Bearing capacity: Terzaghi’s three terms

For a strip footing, Terzaghi’s ultimate bearing capacity is qult = c·Nc + q·Nq + 0.5·γ·B·Nγ, where q = γ·Df is the overburden pressure at foundation level and the N-factors depend only on φ. The three terms read left to right as cohesion, surcharge, and self-weight of the soil wedge. Shape factors scale the equation for square and circular footings. Allowable pressure is qallow = qult / FS with FS typically 2.5–3 — and the exam sometimes asks for the net allowable pressure, which subtracts the overburden q before applying the factor of safety. Read carefully which one is asked.

Slope stability: one ratio

Every slope-stability method — ordinary method of slices, Bishop’s simplified, infinite slope — computes the same ratio: FS = resisting moments (or forces) / driving moments (or forces) along the assumed failure surface. For the infinite slope (a long planar slide parallel to the ground surface, the exam's favourite closed form), FS = [c + (γz·cos²β − u)·tan φ] / [γz·sinβ·cosβ], where β is the slope angle and z the depth to the slip plane. Note the effective-stress form: pore pressure u appears explicitly, reducing the frictional resistance. Rapid drawdown is the classic application — the water level outside drops faster than pore pressures inside can dissipate, so u stays high while the stabilising water weight vanishes, and FS falls.

Lateral earth pressure: Rankine’s coefficients

A retaining wall feels horizontal stress σ′h = K · σ′v. Rankine gives the two limiting states for a frictionless wall with horizontal backfill: Ka = tan²(45° − φ/2) for the active case (wall moves away, soil expands — the smaller coefficient, the design case for most walls) and Kp = tan²(45° + φ/2) for the passive case (wall pushes into soil — the larger coefficient, the resistance in front of embedded walls). At rest, K0 = 1 − sin φ. Total thrust on a wall of height H with no surcharge is P = 0.5 · K · γ · H² acting at H/3 above the base — and with a uniform surcharge qs, add the rectangular pressure block K · qs · H acting at H/2. Worked examples — dry sand, surcharge, a water table in the backfill, the tension crack and passive embedment — are on the Rankine earth pressure problems page.

Key formulas

  • Effective stress: \(\sigma' = \sigma - u\)
  • Consolidation settlement (NC): \(s_{c} = [\frac{H_{0}}{(1 + e_{0})}] \cdot C_{c} \cdot \log_{10} [\frac{(\sigma'_{v0} + \Delta \sigma)}{\sigma'_{v0}}]\)
  • Time factor: \(T_{v} = c_{v} \cdot \frac{t}{H_{dr}^{2}} (T_{v} = 0.848 at U = 90\%)\)
  • Mohr–Coulomb: \(\tau_{f} = c + \sigma'_{n} \cdot \tan \phi\)
  • Terzaghi (strip): \(q_{\text{ult}} = cN_{c} + qN_{q} + 0.5 \gamma\)BNγ
  • Rankine: \(K_{a} = \tan^{2} (45^{\circ} - \frac{\phi}{2})\); \(K_{p} = \tan^{2} (45^{\circ} + \frac{\phi}{2})\); \(K_{0} = 1 - \sin \phi\)

The key formulas are also collected in the formula index.

Worked example

A 3.0 m thick saturated clay layer, doubly drained, has \(e_{0} = 0.90\) and \(C_{c} = 0.35\). The initial vertical effective stress at the layer midpoint is \(\sigma'_{v0} = 100\,\text{kPa}\). A fill imposes an average \(\Delta \sigma = 60\,\text{kPa}\). The clay is normally consolidated. Compute the primary consolidation settlement.

  1. Confirm the branch: normally consolidated, so the full stress increment uses \(C_{c}\).
  2. \(s_{c} = [\frac{3.0}{(1 + 0.90)}] \times 0.35 \times \log_{10} [\frac{(100 + 60)}{100}]\)
  3. = \(1.579 \times 0.35 \times \log_{10} (1.60) = 1.579 \times 0.35 \times 0.2041\)
  4. \(s_{c} \approx 0.113\,\text{m}\) ≈ 113 mm.

Had the clay been overconsolidated with a preconsolidation pressure above 160 kPa, the same increment would use the much flatter \(C_{r}\) branch — always check OCR before choosing \(C_{c}\).

Traps to avoid

  • Total vs effective stress. Shear strength, consolidation, and bearing capacity all run on σ′, never σ. If a problem gives you the water table position, it expects you to subtract u.
  • Log base ten, not natural log. The consolidation settlement equation uses log10; using ln inflates the answer by a factor of 2.3.
  • The (1 + e0) denominator. Forgetting it overstates settlement by nearly a factor of two for typical void ratios.
  • φ = 0 is for saturated clay, UU only. Sands are always drained; assigning them φ = 0 discards their entire frictional strength.
  • Active is the small K. Ka < K0 < Kp, always. If your “active” thrust exceeds the at-rest value, you have the wrong coefficient.
  • Drainage path, not layer thickness. Doubly drained means Hdr = H/2 — and because time scales with Hdr², that halves the thickness but quarters the time.

Soil mechanics feeds directly into Project Sitework (earthwork, excavation support, erosion control) and draws on Groundwater (seepage, pore pressures) — work those pages next, then check where this area sits in the spec on the NCEES coverage map.

Preparing for the PE Civil: Water Resources & Environmental exam?

Work the theory above, then test yourself under timed conditions with the 80-question PE Civil WRE exam simulation — 8 hours, instant scoring, and full worked solutions, from $24.

Want a licensed engineer to look at your weak areas with you? The Premium pass ($99) carries the same three simulations as Triple, but with 30 days of access instead of two weeks — plus direct email access to a licensed civil PE for those 30 days, for up to 10 questions, with replies within one business day.

Try the PE WRE simulation — from $24 →

Free FE/PE flashcards + study tips, by email

Join the Water Resources Hub email list and get the free 40 water-resources flashcards (PDF + Anki) straight away, then study tips and practice problems by email. Email address only — no spam, unsubscribe any time.