Theory explainer
Slope Stability Problems — FE/PE Civil Exam Worked Examples
Slope stability is the geotechnical question with the shortest definition and the longest consequences: will this sloping ground stay where it is? The whole topic is one ratio — resisting shear strength over driving shear stress — applied to three failure shapes: a plane parallel to the surface (the infinite slope), a circular arc through the toe (the slip circle), and a chart value that packages the geometry for you (Taylor’s stability number). Learn which shape the stem is describing, and every problem below is a few lines.
Last reviewed: 2026-11-07. Every worked number below was independently re-solved; steps are shown in full.
What slope stability is: one ratio, three failure shapes
A slope fails when the shear stress mobilised along a potential failure surface exceeds the shear strength of the soil on that surface. Slope stability analysis quantifies that comparison as the factor of safety, FS = shear strength available / shear stress mobilised, always resisting over driving. FS = 1.0 is the point of failure; below 1.0 the slope has failed; design targets sit well above it — commonly 1.5 for permanent slopes and 1.3 for temporary cuts, with 2.0 sometimes required where a structure bears near the crest. The exam tests three failure shapes, and the stem always tells you which one it wants. A translational failure slides on a plane parallel to the ground surface — a thin soil mantle over rock, a long embankment face — and the infinite-slope equation governs it. A rotational failure turns on a circular arc through the toe or below it — an embankment or a cut in fairly uniform soil — and the slip-circle methods (Swedish circle, Fellenius, Bishop) govern it. A wedge or block failure slides on a planar discontinuity such as a rock joint, and the factor of safety is the resisting force over the driving force resolved along the plane. The shear strength in every case is Mohr–Coulomb: τf = c′ + σ′ tanφ′, on effective stress, never total stress.
The infinite slope: dry, then with seepage
Take a long slope inclined at β to the horizontal, with a slip plane parallel to the surface at vertical depth z. A slice of soil one unit wide weighs W = γ z per unit plan area. Resolving that weight normal and parallel to the plane gives the stresses on the slip plane: the normal stress is σ = γ z cos²β and the driving shear stress is τ = γ z sinβ cosβ. The resisting shear strength is c′ + σ′ tanφ′, so the factor of safety is FS = [c′ + γ z cos²β tanφ′] / [γ z sinβ cosβ] for the dry (or moist) case. Two simplifications fall out of it. For a cohesionless soil (c′ = 0) the depth cancels entirely and FS = tanφ′/tanβ — a dry sand slope is stable exactly when the slope is flatter than the friction angle, and any depth the stem gives you is a distractor. And the critical slope angle for a target FS is the β that makes the ratio equal that target: tanβ = tanφ′/FS for cohesionless soil.
Now let the water table rise to the surface with seepage parallel to the slope — the exam’s standard wet case. The pore pressure on the slip plane is u = γw z cos²β, so the effective normal stress becomes σ′ = (γsat − γw) z cos²β = γ′ z cos²β, while the driving stress still uses the full saturated weight: τ = γsat z sinβ cosβ. The factor of safety becomes FS = [c′ + γ′ z cos²β tanφ′] / [γsat z sinβ cosβ], and for cohesionless soil FS = (γ′/γsat) tanφ′/tanβ. Since γ′/γsat is roughly one-half for ordinary soils, seepage roughly halves the factor of safety of a cohesionless slope — Worked Problem 2 shows the full c–φ version, and Worked Problem 5 repeats it in SI units. If the water table sits below the surface at depth hw above the slip plane, the soil above it carries its moist weight and only the submerged part carries γ′: the effective stress becomes σ′ = [γ( z − hw) + γ′hw] cos²β and the driving stress uses the weighted total unit weight the same way.
Circular failure: the Swedish circle, Fellenius, and Bishop
For a finite slope — an embankment, a cut, a dam shoulder — the failure surface is curved, and the exam’s method is to take moments about the centre of a trial circle. The Swedish slip circle (Fellenius) method says FS = resisting moment / overturning moment about the circle centre. For an undrained clay (φ = 0) the shear strength is just cu everywhere on the arc, so the resisting moment is cu times the arc length L = Rθ times the lever arm R, and the whole method collapses to the closed form FS = cuR²θ/(W d), where W is the weight of the sliding mass per unit length of slope and d is the horizontal distance from the toe to the line of action of W. That is Worked Problem 3. The angle θ is the central angle subtended by the slip arc, and it must be in radians — using degrees inflates the answer by a factor of 180/π.
For a c–φ soil the arc is cut into vertical slices and each slice contributes its own resistance: the general Fellenius form is FS = Σ(c′ l + N′ tanφ′) / ΣT, where l is the slice base length, N′ is the effective normal force on the slice base, and T = W sinα is the driving force down the slice base at angle α. Fellenius assumes the interslice forces act parallel to each slice base, which makes it conservative — it typically underestimates FS by 5–15%. Bishop’s simplified method is the refinement the exam names but rarely asks you to iterate by hand: it keeps the interslice normal forces, giving FS = Σ{[c′ b + (W − u b) tanφ′]/mα} / ΣW sinα, with mα = cosα + sinα tanφ′/FS — the FS appears on both sides, so it is solved by iteration. The exam’s expectation, stated on the site’s Geotechnical page, is the concept of slices and moment equilibrium, not a full slice table by hand: know the Fellenius sum, know Bishop is more accurate because it keeps the interslice normals, and know the φ = 0 closed form cold.
Taylor’s stability number and the critical height of a vertical cut
Taylor’s stability number packages the geometry of a finite slope into a single chart value. For a slope of height H in a soil with cohesion c and unit weight γ, the factor of safety is FS = No c/(γH), where No is read from Taylor’s chart for the slope angle β, the friction angle φ, and the depth factor D — the depth to a firm layer divided by the slope height. A toe circle (the arc passes through the toe, D = 1) and a base circle (the arc dips below the toe to the firm layer, D > 1) give different No values, and the critical circle is the one with the smallest FS. For φ = 0 and a toe circle, No is about 5.52 for slopes of 45° or flatter; it falls to about 3.83 for a vertical face. Worked Problem 4 runs a full Taylor calculation. The companion result is the critical height of a vertical cut in φ = 0 clay: Hc = 4cu/γ. A cut taller than Hc fails on its own weight; a cut at height H has FS = Hc/H against that failure. The tension crack that opens at the crest reaches zc = 2cu/γ — half the critical height — and it is the same crack that appears in the cohesive-backfill earth-pressure problem on the Rankine Earth Pressure Problems page. For a quick check: cu = 500 psf and γ = 110 pcf give Hc = 4 × 500/110 = 18.18 ft, a safe height of 18.18/1.5 = 12.12 ft at FS = 1.5, and a tension crack 2 × 500/110 = 9.09 ft deep.
Worked problem 1 Dry cohesionless infinite slope (FE pace, US units)
Given: a long, dry sand slope inclined at β = 25° to the horizontal, with φ′ = 35° and c′ = 0. Find the factor of safety, and the steepest slope angle that still gives FS = 1.5.
Solution:
- Cohesionless and dry, so the depth cancels: FS = tanφ′/tanβ = tan 35°/tan 25° = 0.7002/0.4663 = 1.50.
- For a target FS = 1.5, invert it: tanβ = tanφ′/FS = 0.7002/1.5 = 0.4668, so β = arctan(0.4668) = 25.0° — the slope as given is exactly at the design target.
Answer: FS ≈ 1.50; steepest angle for FS = 1.5 is β ≈ 25°. Trap note: the depth z never enters a cohesionless infinite-slope calculation — if the stem gives you a slip depth for a c = 0 slope, it is a distractor. The second trap is the failure line: FS = 1.0 would need β = φ′ = 35°, so a 35° sand slope is at the point of sliding, not a design.
Worked problem 2 Infinite slope, dry versus saturated with seepage (PE pace, US units)
Given: a long slope inclined at β = 20°, slip plane at vertical depth z = 10 ft, soil with c′ = 100 psf and φ′ = 28°. Moist unit weight γ = 110 pcf; saturated unit weight γsat = 125 pcf; γw = 62.4 pcf. Find FS (a) dry and (b) with the water table at the surface and seepage parallel to the slope.
Solution:
- Geometry: cos²20° = 0.8830; sin 20° cos 20° = 0.3420 × 0.9397 = 0.3214; tan 28° = 0.5317.
- (a) Dry: normal stress σ = γ z cos²β = 110 × 10 × 0.8830 = 971.3 psf. Resisting strength τf = c′ + σ tanφ′ = 100 + 971.3 × 0.5317 = 100 + 516.5 = 616.5 psf. Driving stress τ = γ z sinβ cosβ = 110 × 10 × 0.3214 = 353.5 psf. FS = 616.5/353.5 = 1.74.
- (b) Saturated with seepage: submerged weight γ′ = 125 − 62.4 = 62.6 pcf. Effective normal stress σ′ = γ′ z cos²β = 62.6 × 10 × 0.8830 = 552.8 psf. Resisting strength τf = 100 + 552.8 × 0.5317 = 100 + 293.9 = 393.9 psf. Driving stress τ = γsat z sinβ cosβ = 125 × 10 × 0.3214 = 401.7 psf. FS = 393.9/401.7 = 0.98.
Answer: FS ≈ 1.74 dry, FS ≈ 0.98 saturated — the slope fails when the water table reaches the surface. Trap note: the water cuts the factor of safety nearly in half, and the mechanism is visible in the numbers — the resisting strength falls from 616.5 to 393.9 psf while the driving stress rises from 353.5 to 401.7 psf. The classic slip is putting γsat in the resisting term as well, which gives FS ≈ 1.71 and the wrong “still stable” answer.
Worked problem 3 Swedish slip circle in undrained clay (PE pace, US units)
Given: a trial slip circle through an embankment toe in undrained clay, cu = 800 psf. The circle radius is R = 40 ft and the arc subtends θ = 70° at the centre. The weight of the sliding mass is W = 120,000 lbf per foot of slope length, acting at a horizontal distance d = 10 ft from the toe. Find the factor of safety and judge it against the permanent-slope target.
Solution:
- Convert the central angle to radians: θ = 70° × π/180 = 1.2217 rad. The arc length is L = Rθ = 40 × 1.2217 = 48.87 ft.
- Resisting moment about the centre: MR = cu R²θ = 800 × 40² × 1.2217 = 800 × 1,600 × 1.2217 = 1,563,815 ft·lbf per ft.
- Overturning moment about the centre: MO = W d = 120,000 × 10 = 1,200,000 ft·lbf per ft.
- FS = MR/MO = 1,563,815/1,200,000 = 1.30.
Answer: FS ≈ 1.30 — the slope is standing, but it fails the 1.5 permanent-slope target. Trap note: the angle must be in radians — using 70 instead of 1.2217 would give FS ≈ 74.7, an absurd answer that no distractor list would carry. And 1.30 is not a pass: the exam asks whether the slope is acceptable, and the target is 1.5 for permanent works, so this slope needs flattening, drainage, or a berm before it is accepted.
Worked problem 4 Taylor’s stability number (PE pace, US units)
Given: a 20 ft high slope at β = 45° in a clay with cu = 600 psf and γ = 115 pcf, with φ = 0. A firm layer lies at the toe, so the critical circle is a toe circle (D = 1.0). Taylor’s chart gives No = 5.52 for β = 45°, φ = 0, toe circle. Find the factor of safety and the critical height at FS = 1.
Solution:
- FS = No c/(γH) = 5.52 × 600/(115 × 20) = 3,312/2,300 = 1.44.
- Critical height at FS = 1: Hc = No c/γ = 5.52 × 600/115 = 28.8 ft — the slope could be built about 9 ft taller before it reached limiting equilibrium.
Answer: FS ≈ 1.44; critical height ≈ 28.8 ft. Trap note: the stability number belongs to the circle type and depth factor you actually have — reading No for a base circle (D > 1) when the stem says the firm layer is at the toe, or for the wrong φ, gives a different number and a different answer. And as in Problem 3, 1.44 is standing but short of the 1.5 permanent-slope target.
Worked problem 5 Infinite slope with seepage (SI units)
Given: a long slope inclined at β = 20°, slip plane at vertical depth z = 3 m, soil with c′ = 8 kPa and φ′ = 30°. The saturated unit weight is γsat = 19 kN/m³ and γw = 9.81 kN/m³, with the water table at the surface and seepage parallel to the slope. The dry (moist) unit weight is γ = 17 kN/m³. Find FS saturated, and compare with the dry value.
Solution:
- Geometry: cos²20° = 0.8830; sin 20° cos 20° = 0.3214; tan 30° = 0.5774.
- Saturated: γ′ = 19 − 9.81 = 9.19 kN/m³. Effective normal stress σ′ = 9.19 × 3 × 0.8830 = 24.34 kPa. Resisting strength τf = 8 + 24.34 × 0.5774 = 8 + 14.05 = 22.05 kPa. Driving stress τ = 19 × 3 × 0.3214 = 18.32 kPa. FS = 22.05/18.32 = 1.20.
- Dry: σ = 17 × 3 × 0.8830 = 45.03 kPa; τf = 8 + 45.03 × 0.5774 = 8 + 26.00 = 34.00 kPa; τ = 17 × 3 × 0.3214 = 16.39 kPa; FS = 34.00/16.39 = 2.07.
Answer: FS ≈ 1.20 saturated, versus FS ≈ 2.07 dry. Trap note: kPa and kN/m² are the same unit, so the stress ratio is unit-free — but the submerged weight must be computed in the same unit system as the stem. Using γw = 62.4 pcf in an SI problem, or γsat where γ′ belongs, are the two unit slips this problem is built around.
Frequently asked questions
What is the factor of safety of a slope?
The factor of safety is the ratio of resisting shear strength to driving shear stress along a potential failure surface: FS = shear strength available / shear stress mobilised. FS = 1.0 is the point of failure, FS below 1.0 means the slope has failed, and design commonly targets FS of at least 1.5 for permanent slopes and 1.3 for temporary cuts. A computed FS of 1.30 is therefore standing but not acceptable as a design.
When do you use the infinite slope equation instead of a slip circle?
Use the infinite slope when the failure surface is a plane parallel to the ground surface in a long, uniform slope — typically a thin soil mantle over rock or a long embankment face. Use a circular slip surface (Swedish circle, Fellenius, Bishop) for a finite slope such as an embankment or a cut, where the failure surface curves through the toe or below it. The stem tells you which: words like long slope, plane parallel to the surface, or slip at a depth point to the infinite slope; a trial circle, radius, or centre point to the slip circle.
Why does water make a slope less stable?
Water hurts a slope twice over. First, pore pressure reduces the effective normal stress on the slip plane, which cuts the frictional part of the shear strength. Second, seepage parallel to the slope adds a flow force acting downhill. Worked Problem 2 shows the scale of it: the same slope has FS = 1.74 dry and FS = 0.98 when saturated with seepage parallel to the surface — comfortably stable one day, failed the next. That is why drainage is the fastest route to a more stable slope.
What is the Swedish circle (Fellenius) method?
The Swedish circle method assumes a circular trial failure surface and takes moments about its centre: FS = resisting moment / overturning moment. For an undrained clay (phi = 0) it collapses to the closed form FS = cu x R^2 x theta / (W x d), where cu is the undrained cohesion, R the circle radius, theta the central angle in radians, W the weight of the sliding mass per unit length, and d the horizontal distance from the toe to the weight’s line of action. For c-phi soils the general Fellenius form sums slice by slice: FS = sum(c' x l + N' x tan phi') / sum(T).
What is Taylor’s stability number?
Taylor’s stability number No is a chart value that packages the geometry of a finite slope into one number: FS = No x c / (gamma x H), where c is the cohesion, gamma the unit weight and H the slope height. You read No from Taylor’s chart for the slope angle beta, the friction angle phi and the depth factor D (the ratio of the depth to a firm layer to the slope height). For phi = 0 and a toe circle, No is about 5.52 for slopes of 45 degrees or flatter. Worked Problem 4 runs a full Taylor calculation.
What factor of safety should a slope have?
The usual design targets are FS of at least 1.5 for permanent slopes and 1.3 for temporary cuts, with 2.0 sometimes required where a structure bears near the slope crest. These are design targets, not the failure point — failure is FS = 1.0. Exam stems that ask whether a slope is acceptable are testing the target, not the failure line: a computed FS of 1.30 is standing, but it fails the 1.5 permanent-slope criterion, as in Worked Problem 3.
Free FE/PE flashcards + study tips, by email
Join the Water Resources Hub email list and get the free 40 water-resources flashcards (PDF + Anki) straight away, then study tips and practice problems by email. Email address only — no spam, unsubscribe any time.